botwhe.blogg.se

1. #Renesas usb 3.0 extensible host controller driver windows 7 install#
2. #Renesas usb 3.0 extensible host controller driver windows 7 drivers#
3. #Renesas usb 3.0 extensible host controller driver windows 7 full#
4. #Renesas usb 3.0 extensible host controller driver windows 7 windows 8#

#Renesas usb 3.0 extensible host controller driver windows 7 windows 8#

yet it is on a 3.0 interface and is a 3.0 drive! This is obviously a Windows 8 and Intel issue. In fact, when I plug my drive in, which is a Seagate USB 3.0 drive, in the personalization area under devices, it shows that my "device could perform faster".

I simply looked at transfer speed in windows 8.they are around 25-30 Mb/s. Intel(R) USB 3.0 eXtensible Host Controller- 0100 (Microsoft) I don't believe I have the Renesas controller. Something is wrong the with USB 3.0 driver or the interfaces themselves on the Samsung series 7 (17").for sure.

#Renesas usb 3.0 extensible host controller driver windows 7 full#

Also, it runs fine on my Asus G51SW laptop on the USB 3.0 port, and both external USB 3.0 drives run at full speed on the Asus. An external 3.0 Compact Flash reader (SIIG) can not be read over the USB 3.0 at all, but runs fine on the USB 2.0 side. The other doesn't warn about the connection speed, but it also still runs at USB 2.0 speeds. In the "personalization" menu under devices, one of my devices says "you can run faster with USB 3.0" even though it IS plugged into USB 3.0. All of my USB 3.0 device can connect to the USB interface but they run at USB 2.0 speeds. Just in case you were wondering, I receive no incentive from Intel for anything, so I am not here to help them, but I would like to see the issue resolved correctly. If you run all the tests you can and cannot get the ports to work with the Windows 8 version, I would suggest returning the Motherboard. This fact alone shows me Windows 8 has the necessary drivers, but in some circumstances, they do not work. There is another poster in this thread has the same motherboard as me, and even though my ports work fine, his do not. Some device in one of the USB 3.0 ports is effecting the drivers.Ī problem with the physical connections to the off board ports, which might effect them all.Ī problem with the motherboard/USB 3.0 controller. If your USB 3.0 ports are not working in Windows 8, I would think it is for one of the following reasons. The bottom line is I feel complaining to Intel about needing a driver is not the correct way to address the situation.

#Renesas usb 3.0 extensible host controller driver windows 7 drivers#

I did notice the Intel reference on the extensible controller on my board changed to Renesas after I installed the add-in card.Īll of the controllers and USB Root Hubs (xHCI) are using the same drivers and. I notice the Z79 chipset does not have native Intel USB 3.0, or at least it does not appear to. My ASUS Z77 board already had ASMedia and Intel USB 3.0 controllers. All (including the add-in card) of my USB 3.0 ports are working at 3.0 speeds.

#Renesas usb 3.0 extensible host controller driver windows 7 install#

Since you said you have a Renesas driver, I installed an add-in US Robotics USB 3.0 card to test.ĭid a clean Windows 8 install and no downloaded drivers (no internet connection), so all drivers had to come from the Windows 8 Install media. So wingdam, just in case you have not seen this before, Windows 8 comes with drivers for your USB 3.0 controllers. I have been away from the thread for a while, but I see the comments seem to be about the same.